I agree about the USB Ethernet dongle. Unless you only require short distance wifi range (eg hotel room temp router) the radio in the pi isn’t going to be enough

I built a pi4 router a few years ago, and it’s still running great, I recommend the project. But unfortunately I can’t find the HOWTO and it was before I started taking good notes. I assume your current router is a phone company supplied modem/router?

My setup is cable modem–>pi router–>switch–> old netgear router in Access point only mode

Being that your router/modem is upstream of router, I’m not sure if you could pass-through the WAN to the pi router, and pass back the LAN to the router/modem for the wifi… maybe someone on here can shed some light?

OK daddd (or mommm) it probably is time for me to test my backups haha

Yes this is in addition to the normal alarm. The light is incase I’m sleeping, as I may not hear the basement alarm going off. The notification is if I’m not home.

You had me at “number pad”

The last I knew in the US you have a choice to remove it yourself, you can be as safe or unsafe as you see fit, there a very few rules. Or you pay a company which must follow strict regulation on its removal.

I could have the best self hosted setup… living in a van, down by the river!

This thought came to me this morning. I have 4 machines both because the BEAST grows organically, and because we’re always trying to avoid that single point of failure. Then a scenario comes along that makes you question your whole way of thinking, diversifying may actually create more problems

I didn’t mean to imply that Services actually broke. Only that they didn’t come back after a reboot. A clean reboot may have caused some of the same issues because, I’m learning as I go. Some services are restarted by systemctl, some by cron, some…manual. This is certainly a wake up call that I need standardize and simplify the way the services are started.

Your problem may differ from mine, but whenever I’ve been greeted with the command line in grub the solution has actually been in bios. I’ll leave you with my notes, which are a bit snarky after spending a lot of time trying to figure out hot to repair grub, when the solution was 3 clicks in bios:

"Inspiron won’t boot

Goes to the grub command prompt

Don’t fuck with that thing

Restart, F2 to get into bios

Change boot sequence to start the SSD first, not ubuntu

Reboot, itll do it a couple times, but should boot right into normal grub"

I hope your solution is the same

Slaps forehead I know I read that guide too…whether I forgot about it or thought that would do something else… Thank You!

Me: Hovering mouse over the update button Click it!!

Also me: No no, it says right in the changelog that this is one of biggest releases ever, wait for a point release

Me again: but you can make the “sleep time” automation say Goodnight after it runs!!!

click

The problem with a good running automation is you end up used to them, I forget they’re even there most if the time.

I end up appreciating my once-in-awhile automations more. A couple times a month I need to get up extra early, skip my normal routine and go straight to work. But I’m American, this can’t be done without coffee. The night before I prepare the coffee maker and scan an NFC on the top that turns off the plug and waits for my next alarm, then turns it back on. Once it runs it disables the automation, so I dont accidently burn the house down. Worth a million bucks

In the summer in the northeast US most evenings are cool enough to sleep with just a fan in the window. For the nights that stay too warm past bedtime I scan an NFC on my AC that triggers an automation to shutoff the AC and turn on the window fan at a specified outdoor temp. Saves on electricity and who doesn’t love fresh air??

Btop adds temperature, which htop doesn’t offer… There are a bunch of other *top programs you could check out but btop is a nice one I learned about on Lemmy

The only metric you’ll likely have trouble with is power consumption, I dont think the pi has a sensor for that. You would have to plug it in through a killawatt or smart plug

I’m sorry, what?..Oh, all I heard was that my linux home server is going to be running on new hardware in about a year and a half when all these used computers go on sale. 😁

Yes! Especially automations! I would rather have tags than folders, so an automation could fit into more than one category (eg. Location, action) but I’d take anything over alphabetical!!

Maybe click on that lux entity in the dashboard and see if it has been consistently transmitting its data (on the history graph)? I’m pretty sure you’ll get this warning if the state reads “unavailable” which could be a reception issue or a dying sensor.

I recently saw this happen to an animation of mine and I think this was the cause

I take any chance I can to drop a Chris Barnett link:

Ventoy

I would spend the money on smart switches before smart outlets. I personally find that I want smart control over almost all of my lights/ fans but only some of my outlets.

Another reason for my avoidance of smart outlets is they are much more expensive than smart plugs and it’s rare that you want to control both plugs in an outlet anyways.

As far as wiring if you want window/ door sensors or motion sensors you might consider running power to those locations. Much better than changing button batteries constantly.

Use conduit to future proof any network cables you run…

That’s all that comes to mind at the moment

Should be able to just do it with automations and include “choose” action. 2024.1 looks like it makes it easier building blocks.